24 Hour Plumber Perth: May 2014

Wednesday, 28 May 2014

Tuesday, 27 May 2014

Have you run your bath water only to realise its ice cold? Have you jumped in the shower and been sprayed by cold water? If so, chances are you have a problem with your homes hot water system. Don’t stress, there are a few basic things you can try yourself prior to calling a plumber. If you have a natural or propane gas water system, chances are the pilot has gone out. The pilot is a small flame that ignites the gas burner on your system. When it goes out, first try relighting it, following the directions on the label, which is often on the front of the system. If the pilot doesn't relight, or if it goes out right after lighting, by far the most common cause is a broken thermocouple. The good news: you can usually replace a thermocouple for minimal cost and in less than an hour from a local hardware. You'll get your hot water going without waiting for a pro to show up and save a few dollars!

To replace the thermocouple, be sure to turn off the shutoff valve in the gas line; that is, one quarter turn so that the handle is at a right angle to the pipe. Since working room is tight around the burner, we recommend that you simply unscrew the three nuts at the control valve and pull out the entire burner assembly unit. You'll see either a slot or clips that hold it in its place. Then either unscrew the thermocouple end or pull it out (depending on the water heater) and take it with you to hardware store to find a match. Position it exactly the same way as the old one. The pilot flame should wrap around the thermocouple bulb.

To reattach the three lines to the gas valve, thread the nuts into place with your fingers and hand-tighten them properly. Then snug them up with a quarter to half revolution with a wrench. The metals are soft, so don't over tighten as they will break.

Be sure to test for gas leaks. You must have the pilot lit and the burner on for this test so that gas is flowing through the large tube on the system. Reopen the shutoff valve, relight the pilot, then turn the control valve to the “on” position. When the gas burner is on, use a 50/50 dish soap/water mix to test the screw joints for air bubbles that indicate leaks.

If you have an issue with a blocked drain Perth or hot water system Perth, then you need a 24 hour plumber Perth or an emergency plumber Perth to service you. You might also reach out to a gas plumber Perth to help you. Its important that you have a plumber Perth or a Perth Plumber you can trust.

Sunday, 18 May 2014

Reasons For A Running Toilet

Have you ever wondered why you have a running toilet? Firstly, it is important that you acknowledge the fact that every hand made device is always bound to break and this is no exception with your toilet. Therefore, in case you realize that your toilet is running, you should never be worried at all; instead, simply take some time and figure out why is running out, and then consider repairing it.

For you establish the main cause of the problem in your toilet, it is paramount to remove the top tank of the toilet and place on a secure location. Try pushing the toilet’s flush lever and examines what happens.

On many occasions, one will be in agreement with the fact that one of the reasons why the toilet runs is simply because one or all of the following has/have problems.

· Tank ball

· Ball cork

· Intake valve and/or

· Float ball

Having identified the reason why your toilet is running, it is then important to think of a way of repairing it. So how do you fix a running toilet?

There are complicated aspects in the toilet repair that inexperienced cannot handle. Therefore, consider hiring experienced personnel first.

Check if the spare parts in the toilet tank require any replacement or just repair. It is important to note that different people use various mechanisms. However, all these normally lead to the same answers.

Try checking if the chain is in contact with the flapper. It is important to thread the flapper chain using a plastic straw as this prevents long chain from sticking on things. Complete replacement of the chain is another remedy for this. You can achieve this by using a dental floss made loop having a similar length to the chain.

Also, it is important to ensure that the water is filled to the water line as lack of water is what basically makes the toilet to run.

Another tip for fixing the running problem is through adjusting the float and valve. By using your hands, you can pulp up the float. If the action stops the water flow, it is advisable to adjust the float level in order for the tank to stop filling having attained the required amount of water flow, slightly below overflow tube top.

Finally, ensure that the flapper is well cleaned to prevent a repeat of the running. Dirty flappers have always been blamed for the leaking of the toilets. This should then be followed by troubleshooting any other problem in your toilet in order to function normally.

Emergency Plumber Perth

f you have an issue with a blocked drain Perth or hot water system Perth, then you need a 24 hour plumber Perth or an emergency plumber Perth to service you. You might also reach out to a gas plumber Perth to help you. Its important that you have a plumber Perth or a Perth Plumber you can trust.

Plumber Perth Tips

Bathroom Plumbing

Having guests visiting for the holidays leads to increases in toilet use, so be sure to tell your guests not to put sanitary products, napkins, or baby wipes in the toilet. Not everyone knows that these items belong in the trash and not in the toilet!
Ask your guests to use all the toilets in the house to reduce the load on a single toilet and decrease the chance of it getting backed up.
Make sure there are no items on top of the toilet tank lid and remove any items you may have hanging near or over the toilet bowl. Guests are not used to the way things are positioned in your home and they may accidentally knock an object into the toilet!
In case of a blockage in your toilet, do not keep flushing: use a plunger to try and dislodge the blockage.
If your toilet keeps running on, check the position of the flapper inside the tank. It has to fit over the hole in the base of the tank, if it’s not fitting properly, use the shut off valve, which is normally located under the tank.
Place hair traps in all showers and tub drains, as you will have extra guests taking showers and that will add to the amount of hair going down the drain.

Kitchen Plumbing

A lot of cooking will be happening in your kitchen during the holidays. Make sure that whoever is helping you in the kitchen knows what should go in the trash, what can go in the bio container and what ought to go in the garbage disposal (if you have one).
Avoid putting pasta, rice, coffee grounds, bones, potato skins, egg shells, lettuce or any large amounts of food down the garbage disposal. Remember to run cold water when using it.
Be sure to never pour that turkey grease or ham fat down the drain and if you don’t have a garbage disposal make sure you have a strainer in your sinks.
If your kitchen sink (or any sinks!) gets blocked use this vinegar and baking soda solution to help unclogged your drain.
For dishwashers, make sure you’re removing the food scraps from the dishes and cutlery and rinsing them in the sink so that the debris doesn’t block the dishwasher water line.

If you are having further issues, get in touch with a great plumber from Melbourne 24 Hour Plumbing , Mr Plumber Sydney, Manly Emergency Plumber, Geelong 24 Hour Plumbing, localplumber gold goast , plumber adelaide plumber brisbane

Monday, 12 May 2014

Reasons For A Blocked Drain Perth

It's a busy Monday morning and of all things that could go wrong, you notice that your drain is blocked. This may seem like reason for panic, but never fear, it's probably easier to fix than you think, even if you aren't the most handy of people. The first step to fixing a blocked drain is to figure out why, so you can see if you need to enlist in the help of a professional, or if it is a DIY project. A few common causes for a blocked drain include:

-Foreign Objects or Debris

This can be hair from the shower, or something your four year old decided to flush. Blockage caused by an object or debris are the simplest to fix. You can try a couple of techniques. One is the boiling water strategy. This is as easy as it sounds, just bring water to a boil and pour it down the drain that is clogged. You may have to repeat a few times for results. Another tactic is using baking soda and vinegar. Mix one third cup of each and let the fizzy mixture sit overnight, then rinse with hot water. You could also try using a rod or coat hanger to move the obstruction. Use hot water to loosen the object, then use the rod to clear the debris.

-Too Much Water

This can be caused from a storm or a flood, and occurs when there is too much water in the pipe that it may not be built to handle, or if a toilet is flushed in excess. This type of blockage can cause flooding from the toilet or pipe which gets very unpleasant. This problem is fixed by draining the water, which can be tricky, so call a plumber for this one.

-Broken Pipe or Incorrect Installation

A broken pike can occur during bad weather or a heavy object. It can also occur when too much pressure is put on the pipes, either from water or debris. A cause for drain issues may also be incorrect installation, which you will need a professional to fix.

Water Flow Issues

-If a pipe doesn't run downhill, then the water cannot flow with gravity, making blockages a common occurrence. Try first using a plunger to unclog the blockage, but if you find that it doesn't work, or happens often, you may consider calling a professional to fix the installation of the pipes.

If you are having further issues, get in touch with a great plumber from Melbourne 24 Hour Plumbing, Mr Plumber Sydney, Gold Coast Emergency Plumber, Adelaide 24 Hour Plumbing or Mr Plumber Perth.

Blocked drain perth, hot water system perth, 24 hour plumber perth, emergency plumber perth, plumber perth, perth plumber, gas plumber perth

Monday, 5 May 2014

Perth Plumbing Tips

Plumbing is a varied and skilled profession that includes many diverse areas of the job. Some plumbing tasks should be left to professional plumbers for reasons of safety and health. Plumbing jobs that entails working on gas channels of inner heating boilers must actually be left for professional heating engineers or gas fitters, as a mistake would cost a person’s life. There are lots of DIY plumbing maintenance that you can perform yourself without exposing yourself in danger.

Watching out your plumbing system may appear like a huge task, maybe even anything that must be left to a professional plumber. And whilst this is actually true for a number of projects such as repairing breaks, leaks, cracks, power failure and frozen pipes, there are simple methods that you as the home owner may assist to make sure that your plumbing mechanism runs smoothly. Offering simple repair for your plumbing mechanism will ensure that it is properly maintained, and would hopefully assist to minimize the amount of visits required from an expert plumber to handle larger problems.

For instance, dripping pipes may be irritating to say the slightest, but dripping pipes that are left unattended to for long durations may cause fair amounts of damage to properties. Most drips result from poorly fitted joints of pipes. These pipe joints may be found n several applications that include:

Bath traps, basin traps and kitchen sinks are all linked to the waste-water pipe by use of a threaded joint; when the joint leaks it may cause damages to units, floors or anything below the joint. The most excellent method to remedy this kind of leak is removing the connecting nuts and ensuring that the rubber washers are present and in perfect conditions. The next measure is making sure that the pipes are pushed completely into the fittings on the traps. A perfect idea is binding the threaded parts of the traps with thread tapes or PTFE to ensure good seals.
Leaks for mechanical joints or compression joints may also be repaired in a similar manner. Compression joints are usually maintenance free although if they are interrupted the joint may start leaking. If you get one of such joints leaking the most excellent thing to perform is isolating the water and draining the pipe work completely. This may be carried out in most instances by unlocking the taps. Carefully loosen the joint using a spanner; it is an excellent idea to have some kind of towel or container under the joint so that it can capture any residual moisture that might be left inside the pipe work. Fully undo the nut and then join the joint treads with PTFE tape, retighten the nut to complete the repair.

24 Hour Plumber Perth